sE‘s reinterpretation of a proven European all-rounder
Classic sound meets modern craftsmanship; we are proud to re-introduce the improved sE4400, multi-pattern large-diaphragm true-condenser microphone! Hand-crafted with the highest attention to detail, built with a roadworthy die-cast all-metal housing, metal switches, and rugged spring steel wire mesh grille that can take a beating during day-to-day tour life. The sE4400 appeals with its down-to-earth elegance, offering discrete electronics prioritizing the features you really need. The sE4400 brings sought-after classic sound back to mic lockers worldwide. The sE4400's metal switches...
let you select between 4 polar patterns; from cardioid to omnidirectional or figure-eight to hypercardioid. Whereas the switchable attenuation pads and low-cut filters compensate for loud vocals, guitars, drums, and brass instruments - and easily tame excessive low-frequency rumble or proximity effect. The sE4400 comes with a hand-crafted, gold-sputtered, dual-diaphragm capsule to capture sound sources of all kinds with breathtaking clarity and precision, be it in demanding studio or fast-paced live environments.
Free of thrills, No LEDs. No plastic switches.
Select between 4 polar patterns with metal switches, from cardioid to omnidirectional or figure-eight to hypercardioid, with a gold-sputtered, dual-diaphragm capsule for precision-based miking techniques to minimize signal bleed from unwanted sources in demanding studio or fast-paced live environments.
Hand-crafted 1" true condenser capsule
Individually tuned and cared for by sE’s skilled technicians, each sE4400’s hand-crafted, gold-sputtered, dual-diaphragm capsule captures sound sources of all kinds with breathtaking clarity and precision, be it in demanding studio or fast-paced live environments.
Switchable pre-attenuation pad
Select between two pre-attenuation pads for an extended dynamic range and compensate for loud vocals, guitars, drums, and brass instruments.
Switchable low-cut filter
Easily tame excessive low-frequency rumble and proximity effect with two low-cut filters and efficiently adjust for close-miking techniques.
Dent-proof metal housing with premium finish
Hand-crafted with the highest attention to detail, built with a roadworthy die-cast all-metal housing, metal switches, and rugged spring steel wire mesh grille, the sE4400 is built to last for years of demanding studio use and the day-to-day life of a touring artist.
Available in Matched Pair Configurations
Each sE4400 Matched Pair is rigorously tested, tuned in-house and sonically matched to ensure a virtually identical frequency response for balanced, consistent sound. Complete with a metal mic case, stereo bar, two shockmounts and two sE4400 microphones.
| Components | |
|---|---|
| Capsule | Hand-crafted 1" Gold-sputtered True Condenser |
| Diaphragm | Gold-sputtered mylar |
| Power | |
| Electrical impedance | 22 Ohms |
| Connectivity | 3-pin male XLR connector |
| Powering | 48V Phantom Power (P48 according to IEC 61938) |
| Sound | |
| Polar patterns | Cardioid, Hypercardioid, Omni-directional, Figure-8 |
| Frequency range | 20 Hz - 20 kHz |
| Sensitivity | 25 mV / Pa (-32 dBV) |
| Max SPL | 137 / 147 / 157 dB (0/10/20 dB Attenuation pad - 0.5% THD) |
| Equivalent noise level | 13 dB(A) |
| Signal to noise ratio | 81 dB |
| Low-cut filter | 40 / 80 Hz, 6 dB/Oct, switchable |
| Attenuation pad | 10 / 20 dB, switchable |
| Dimensions | |
| Mic weight | 290 g (10.23 oz.) |
| Mic length | 146 mm (5.75 in.) |
| Mic width | 58 mm (2.32 in.) |
| Mic diameter | 29 mm (1.10 in.) |
| What's in the sE4400 box | |
| sE4400 microphone | |
| Custom shockmount + thread adapter | |
| Metal case | |
